Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
Have you been interested in info around A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old bathtub is readily obtainable, the task can relocate immediately; if you need to open a wall to eliminate the old bathtub as well as place the brand-new tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will require a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the job as well as fit trying it. As opposed to hiring a service provider to take control of a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This short article will help you set up a brand-new bathtub in your restroom if you have actually currently bought a brand-new tub as well as don't require to alter the arrangement of your previous water system pipelines.
Your tools and material list ought to comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome due to the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to carrying on to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers are in place in between the tap and also the sink. Protect the faucet in position with the supplier provided backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind must be connected to the tap ends first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required setting. The wood boards are useful in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub needs to wait till the tub has been made use of at least when as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the supporting framework supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, leading to difficulties with moisture and also possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub is in use. The sealant can break relatively early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic person who reads about How to Install a Bathtub, I think sharing that piece of content was really helpful. You should take the time to share this write-up if you liked it. I praise you for your time. Kindly check up our site back soon.
Plumbing excellence awaits. Report this page